How to Replace Carpet in a Boat?

Last Updated on September 18, 2022

Do you have a boat that desperately needs a new carpet? Are you not sure how to go about replacing it? Well, don’t worry, because I am here to help!

This can be a daunting task for those who have never done it before, but with our step-by-step guide, you’ll be replacing your boat’s carpet like a pro in no time!

We’ll cover the supplies you’ll need, the steps you’ll need to take, and even some tips for a successful project. So read on for all the information you need on this topic!

How To Install Marine Carpets In Your Boat?

  • First, remove the old carpet from your boat. You can do this by pulling it up from the corners or by cutting it into strips with a utility knife.
  • Next, clean the floor of your boat to prepare for the new carpet. Be sure to remove any dirt, debris, or adhesive residue
  • Once the floor is clean, lay down a layer of adhesive and then place your new carpet on top.
  • Start at one end and work your way to the other, trimming as needed.
  • Finally, secure the edges of the new carpet with marine-grade tape or staples.
  • This will ensure that your new carpet stays in place no matter what kind of weather or waves you encounter while out on the water!

How Do You Replace Old Boat Carpet?

Assuming you mean replacing the carpet on the floor of a boat: You will first need to remove the old carpet. To do this, you will need to lift up each section of carpet and peel it back until it is all removed.

Once the old carpet is removed, you can clean the flooring beneath it to prepare for the installation of the new carpet. When installing a new boat carpet, be sure to use marine-grade carpet that is specifically designed for boats. 

This type of carpet is resistant to mold and mildew and can withstand exposure to sun and water. It is also important to use a good quality adhesive when installing new boat carpets so that they will stay in place and not come loose over time.

How Do You Remove Carpet from a Boat?

If you’re looking to remove carpet from your boat, there are a few things you’ll need to keep in mind.

First, you’ll need to make sure you have the right tools for the job. A utility knife, scissors, and a putty knife will all come in handy. You’ll also want to gather some old towels or rags to help with the clean-up.

Then, use your utility knife to score along the edges of the carpeting. This will help make removal easier. 

Next, use your putty knife or scissors to lift up a corner of the carpeting and begin peeling it back.

Work slowly and carefully so that you don’t damage the underlying flooring. As you remove the carpeting, be sure to vacuum up any loose fibers or debris. 

Once everything is removed, give the area a good cleaning before replacing any furniture or other items. And that’s it! With a little time and effort, you can easily remove carpet from your boat yourself.

Can You Put New Carpet Over Old Carpet on a Boat?

Many boat owners are faced with the question of whether or not to replace their old carpets. While a new carpet can certainly provide a more polished look, it may not be necessary to completely rip out the old carpet. 

No, you cannot put a new carpet over the old carpet on a boat. The old carpet will need to be removed before the new carpet can be installed.

How Do You Replace Carpet in an Aluminum Boat?

Carpet in an aluminum boat can be replaced by first removing the old carpet. This is done by unscrewing the staples or adhesive that is holding it in place. Once the old carpet is removed, you will need to measure and cut the new carpet to fit.

It is important to make sure that the new carpet is cut correctly so that it will lay flat and not bunch up when installed. After the new carpet is cut, it can be glued or stapled into place.

How to Replace Carpet in a Boat?

How to Replace Carpet in a Fiberglass Boat?

If your fiberglass boat is looking a little worse for wear, you might be considering replacing the carpet. This is a big job, but it’s not impossible to do yourself. 

Here’s how to replace the carpet in a fiberglass boat:

Step 1: Remove the old carpet. This will involve taking up the old adhesive and removing any staples or tacks that are holding it in place.

Step 2: Clean the surface. Once the old carpet is removed, you’ll need to clean the surface beneath it. Use a cleaner that is specifically designed for fiberglass boats and scrub away any dirt, grime, or mildew that has accumulated.

Step 3: Install new carpet padding. This step is optional, but if you want your new carpets to last longer, it’s worth installing some padding underneath them. You can purchase special boat padding at most marine supply stores.

Step 4: Cut the new carpet to size. Measure your boat’s deck carefully and cut the new piece of carpeting slightly larger than necessary. This will give you some wiggle room when it comes time to install it. 

Step 5: Adhere to the new carpeting in place. There are several ways to do this, but one of the easiest is to use double-sided tape. Apply strips of tape around the perimeter of the deck and then lay down the new carpet, pressing it into place to make sure it adheres well.

Step 6: Trim off any excess carpeting around the edges with a sharp knife or scissors once you’re happy with how it looks. And that’s it! You’ve successfully replaced the carpeting in your fiberglass boat all by yourself!

Cutting Boat Carpet Corners

If you’re looking for a way to make your boat carpeting look even better, consider cutting the corners. This simple technique can give your boat’s interior a neater appearance and help the carpet last longer. 

1. To cut boat carpet corners, start by measuring the length and width of the area you want to cover.

2. Then, use a sharp knife or scissors to cut the carpeting to size. When cutting, be sure to leave about an inch of extra material around all four sides so that you can tuck it under the trim. 

3. Once the carpet is cut to size, place it in the desired location and use a utility knife or scissors to trim away any excess material. Be careful not to cut too close to the edge of the carpet, as this could cause it to unravel. 

4. Finally, use adhesive tape or heavy-duty staples to secure the corners in place. With just a little bit of effort, cutting boat carpet corners can give your vessel’s interior a polished look. 

Replace Boat Carpet With Seadek

If you are considering replacing your boat’s carpet, you may want to consider using SeaDek instead. SeaDek is a marine flooring product that has many benefits over traditional carpets. 

It is made of closed-cell EVA foam, which makes it very durable and resistant to mold and mildew. It is also non-slip, making it safer for you and your passengers. Installation is easy and does not require any special tools or techniques.


Replacing boat carpets can seem like a daunting task, but with the right tools and instructions, it can be done on a weekend. We’ve provided you with everything you need to know before starting your project. 

From choosing the right type of carpet to considering the installation process, we have you covered. We also attached a video tutorial that will walk you through each step of the replacement process. So what are you waiting for? Get started today!